SAP Data Services Connector configuration

What is it?

The Connector.config file tells the SAP Data Services Connector where to send web service calls and where to find the WSDL that describes those calls. It is a plain text INI-style file with two sections: [CONNECTOR] and [DATA SERVICES]. After you install the connector, you must edit this file before any SAP Data Services job will run.

Before you start

Make sure the following are in place before editing the file:

• The connector is installed at <OpConxps>\SAPDataServices. See SAP Data Services Connector installation.
• You know the address (host and port) of the SAP Data Services web server.
• You know whether your SAP Data Services installation uses the default web services endpoint (/DataServices/servlet/webservices?ver=2.1) or a custom one.

Configure the file

To configure the connector, complete the following steps:

1. Open Connector.config in the connector installation directory in a text editor.

2. In the [CONNECTOR] section, leave CONNECTOR_NAME unchanged. This value should not be changed from its delivered setting.

3. In the [CONNECTOR] section, set DEBUG:

   Value	When to use
   OFF	Normal operation. This is the default.
   ON	Only when requested to capture an error condition.

4. In the [DATA SERVICES] section, set DATA_SERVICES_SERVER_ADDRESS to the address of the web server hosting the SAP Data Services web service (for example, http://VM-SAP-DS:8080). This value overrides the web server address in the supplied WSDL.

5. In the [DATA SERVICES] section, set DATA_SERVICES_WEB_SERVICES_ENDPOINT. Use the default value /DataServices/servlet/webservices?ver=2.1 unless the endpoint was changed during the SAP Data Services installation.

6. In the [DATA SERVICES] section, leave DATA_SERVICES_WSDL_LOCATION unchanged. This value should not be changed.

7. Save the file.

Connector.config is now ready for the connector to use on the next job run.

File template

The empty file has the following structure:

[CONNECTOR]
CONNECTOR_NAME=
DEBUG=

[DATA SERVICES]
DATA_SERVICES_SERVER_ADDRESS=
DATA_SERVICES_WEB_SERVICES_ENDPOINT=
DATA_SERVICES_WSDL_LOCATION=

Settings reference

[CONNECTOR] section

Setting	Description	Default	Notes
CONNECTOR_NAME	The name of the connector.	(delivered value)	Do not change.
DEBUG	Connector debug mode.	OFF	Set to ON only when requested to capture an error condition.

[DATA SERVICES] section

Setting	Description	Default	Notes
DATA_SERVICES_SERVER_ADDRESS	Address of the web server that hosts the SAP Data Services web service.	(none)	The value here overrides the web server address in the supplied WSDL.
DATA_SERVICES_WEB_SERVICES_ENDPOINT	Endpoint for the SAP Data Services web services.	/DataServices/servlet/webservices?ver=2.1	Use the default unless the endpoint was changed during the SAP Data Services installation.
DATA_SERVICES_WSDL_LOCATION	Location of BODS_WSDL.wsdl relative to the connector installation directory.	wsdl/BODS_WSDL.wsdl	Do not change.

Example

Example

A typical Connector.config:

[CONNECTOR]
CONNECTOR_NAME=SAP Data Services Connector
DEBUG=ON

[DATA SERVICES]
DATA_SERVICES_SERVER_ADDRESS=http://VM-SAP-DS:8080
DATA_SERVICES_WEB_SERVICES_ENDPOINT=/DataServices/servlet/webservices?ver=2.1
DATA_SERVICES_WSDL_LOCATION=wsdl/BODS_WSDL.wsdl

Next steps

After the file is saved, continue with:

• Set up the SAP Data Services Global Property to make the connector path easy to reference from jobs.
• Install the job subtype for your UI: Enterprise Manager or Solution Manager.
• Define a SAP Data Services job and run a PING to verify the configuration end-to-end.

FAQs

When should I enable DEBUG? Enable DEBUG (ON) only when requested to capture an error condition. The connector should otherwise run with DEBUG disabled (OFF).

Do I need to change the WSDL location? No. DATA_SERVICES_WSDL_LOCATION should not be changed.

What if my Data Services installation uses a different endpoint? The default /DataServices/servlet/webservices?ver=2.1 should be used unless the endpoint has been changed during the SAP Data Services installation. If it has, enter the customized endpoint value in DATA_SERVICES_WEB_SERVICES_ENDPOINT.

Why does DATA_SERVICES_SERVER_ADDRESS need to be set if it's already in the WSDL? The value in Connector.config overrides the address that ships in BODS_WSDL.wsdl. Setting it here means you do not have to edit the WSDL when the SAP Data Services host or port changes.

How do I verify the configuration works? Define a job with the PING job type and run it. PING tests the communications link between the connector and the SAP Data Services environment without running a batch job.

Glossary

Connector.config — The configuration file for the SAP Data Services Connector. Renamed from Agent.config in version 21.

Endpoint — The URL path on the Data Services web server where the connector sends web service requests.

WSDL — Web Services Description Language file. The connector uses BODS_WSDL.wsdl to define the web service operations it can call against SAP Data Services.

PING job type — A connector job type that has no parameters and is used to test the communication path between the connector and SAP Data Services.